Electric Hydraulic Power Unit (eHPU)

ProTorque’s Electric Hydraulic Power Unit (eHPU) transforms rig operations with a focus on efficiency, reliability, and reduced downtime. This rig-integrated unit draws power directly from the rig grid, replacing diesel-powered HPUs. Experience streamlined operations, simplified maintenance, a significant impact on rig time savings and a reduced environmental footprint.

#RedefineTRS™

FEATURES

Seamless integration with existing rig power, eliminating separate fuel-based units

Provides fewer tong trucks in use and on the road

Faster setup and tear-down compared to traditional hydraulic power sources

Engine-free design minimizes failure points and increases uptime

Fewer moving parts reduce maintenance requirements and downtime risks

Eliminates fuel expenses and lowers ongoing maintenance costs

ALL SERVICES, ALL LOCATIONS

Contact Us today!

Flush Mounted Spider – FMS

Flush Mounted Spider (FMS)

ProTorque offers the Flush Mounted Spider. This advanced rotary system delivers unmatched casing handling through replaceable die carriers and integrated back-up torque of up to 50,000 ft/lbs. Leverage streamlined, automated casing operations that outclass traditional methods.

#RedefineTRS™

FEATURES

Holds the weight of the casing string

Replaceable die carriers for superior casing control

Powerful backup torque (up to 50,000 ft/lbs) eliminates the need for manual tongs and separate backup systems

Low-profile design integrates into the rotary table

Streamlined processes reduce pinch points and increase overall rig floor safety

SPECIFICATIONS

* With addition of the adapter ring, same FMS can be used with any other most common 37 1/2″ rotaries: national or EMSCO configuration

Heading #3	Heading #3
MAXIMUM TENSION RATING	350 TONS
MAXIMUM WORKING PRESSURE	2000 PSI (13,790 kPa)
FLOW RATE REQUIRED	34 GPM (128 LPM)
MASS (TOOL ONLY)	2,900 LBS (1,315 KG)
MASS RANGE (CARRIERS AND GUIDE PLATES INCLUDED)	3,050-3,700 LBS (1,383-1,678 KG)
TIME TO EXTEND AND RETRACT	6 SECONDS
COMPATIBLE ROTARY TABLE	27 1/2”, 37 1/2*
CASING SIZE RANGE	13.625″ – 2.375″

*MAXIMUM TORQUE AT 2000 PSI WORKING PRESSURE ON A SINGLE JOINT

* torque values are determined by slip upon the pipe and not the limitations of the tool

Heading #3	Heading #3
MAXIMUM TENSION RATING	50,000
MAXIMUM WORKING PRESSURE	38,000
FLOW RATE REQUIRED	30,000
MASS (TOOL ONLY)	22,000
MASS RANGE (CARRIERS AND GUIDE PLATES INCLUDED)	14,000

ALL SERVICES, ALL LOCATIONS

Contact Us today!

Bottom Hole Assembly (BHA) Frame

MOBILE BOTTOM HOLE ASSEMBLY (BHA) FRAME

The ProTorque BHA frame brings all of the make and break capabilities of a shop bucking unit and puts them in a mobile package. The frame can be shipped direct to your sites rather than shipping individual items to and from locations. The bucking frame consists of a tubular spinner, hydraulic stationary backup and a torque head with an adjustable span of up to 18 inches between the jaws. The four jaw design can accommodate pipe from 4 ½”” – 12” and up to 100,000 ft/lbs of torque. The frame safely assembles and disassembles any rotary shouldered connection(s). It is designed to assemble the bottom hole assembly offline. The horizontal position allows the operator to safely and easily align the threaded connection off the critical path. This reduces risk to employees on the rig floor as well as the chance of damage upon make-up or break-out, because the process is carried out off the critical path. The ProTorque Mobile BHA frame makes the process safer, saves valuable rig time and helps to reduce cost. All connections are able to be torque monitored, and a copy of those make up charts will be available on site.

The BHA frame is just another innovative way. ProTorque is redefining TRS. By striving for advancements in technology within our industry, we are known as one of the most technically advanced casing running solutionists on the market.

#RedefineTRS™

FEATURES

Single application savings up to 65%

Increase safety on rig floor

Efficient Use of Time (EUT)

Mobile design for direct on-site deployment

Run double or triple stands of drill pipe to save rig time

Reduce Carbon Footprint

SPECIFICATIONS

Heading #3	Heading #3
PIPE SIZE RANGE	4 ½”-12”
TORQUE RANGE	100,000 ft/lbs
WEIGHT	10,100 lbs
DIMENSIONS	95”L X 90”W X 57”H
BACK-UP JAW ADJUSTMENT (SCOPE)	18”

ALL SERVICES, ALL LOCATIONS

Contact Us today!

RCD Press

RCD PRESS

The RCD (Rotating Control Device) Press is used to install or remove a tubular onto an RCD Head. The head is used with Managed Pressure Drilling (MPD) and is conventionally installed on the rig floor. This method of installation can cause a variety of handling and safety concerns. When installing ahead on the rig floor, the rig cost is Non-Productive Time (NPT) so by taking this operation offline we are able to remove the hazards and costs associated.

#RedefineTRS™

FEATURES

Safe and efficient installation process

Reduces hazards and NPT on the rig floor

Inline time savings equate to a more productive operation

SPECIFICATIONS

Heading #3	Heading #3
PRESS STROKE LENGTH	36” (914.4 mm)
OVERALL HEAD LENGTH (MAXIMUM)	52” (1,320 mm)
HEAD OD (MAXIMUM)	24” (609 mm)
TUBULAR OD (RANGE)	3 – 7.63” (76.2 – 193.8 mm)
UNIT PRESSURE RATING (MAXIMUM)	3,000 PSI (20,700 kPa)
HYDRAULIC FLOW REQUIREMENTS	5 – 70 gal/min (19 – 265 L/min)

ALL SERVICES, ALL LOCATIONS

Contact Us today!

Mobile Bucking Frame

BUCKING FRAME

The Bucking Frame, when coupled with any power tong, can be used for making and breaking out threaded connections. The compact footprint can be utilized in even the most remote locations and it safely assembles and disassembles connections for casing accessories (float shoe / collar), pups, hangers and many other threaded tools.

#RedefineTRS™

FEATURES

Adjustable Back-ups

Reduces hazards and NPT on the rig floor

Inline time savings equates to more productive rig time & seamless operation

Protorque Bucking frame for oil and rigs

SPECIFICATIONS

Heading #3	Heading #3
PIPE SIZE RANGE	Power Tong 4.5 – 13.63” (114.3 – 346 mm) Back-up jaw 4 – 15” (101.6 – 381 mm)
TORQUE RANGE	4.5 – 5.5” (114.3 – 139.7 mm) 25,000 ft/lbs (33,850 Nm) 7 – 13.63” (177.8 – 346 mm) 35,000 ft/lbs (47,400 Nm)
FLOW RATING	40 – 60 GPM (152 – 227 LPM)
WEIGHT	4,500 lbs (2045 kg)
DIMENSIONS	Length 95” (2,413 mm), Width 58” (1,473 mm), Height 68” (1,727 mm)
HEIGHT ADJUSTMENT	12” (305 mm)
BACK-UP JAW ADJUSTMENT (SCOPE)	Maximum 52” (1,321 mm) Minimum 9” (229 mm)
	All specifications are power tong dependent

ALL SERVICES, ALL LOCATIONS

Contact Us today!

Break-Out Vise

BREAK-OUT VISE

The Break-Out Vise was designed to work with the Petol brand Tong & Chain Vise. A variety of torque ratings are available upon request. The compact footprint, along with a mobile support stand, allows the assembly to be installed into even the smallest areas for making and breaking rotary shoulder connections.

Used primarily for CRT tools, the vise and adjustable roller stand allows you to both make and break connections. This is accomplished inside of the same footprint by simply shifting or rotating the tool. The Break-Out Vise’s compact footprint and mobile support stand allow the assembly to be installed into the smallest areas. A variety of torque ratings are available upon request. From make-up to break-out in mere minutes.

#RedefineTRS™

FEATURES

Sliding head design allows for vise or adjustable roller to be moved for make / break operations

Lift ram for installation and removal of tong after operation

Independent hydraulic control stand available upon request

Low flow hydraulic system allows for controlled use

SPECIFICATIONS

Heading #3	Heading #3
TORQUE RATING	40,000 – 90,000 ft/lbs (54,230 – 12,2025 Nm)
TUBULAR OD RANGE	4 – 14” OD
DIMENSIONS	Length 60“ (1,524 mm), Width 46” (1,168 mm), Height 56” (1,422 mm)
WEIGHT	1,500 lbs (680 kg)
PRESSURE RATING	3,000 PSI (20,700 kPa)
HYDRAULIC FLOW REQUIREMENTS	2 – 8 gal/min (7.5 – 30.5 L/min)

ALL SERVICES, ALL LOCATIONS

CONTACT US TODAY

Vacuum Drift

VACUUM DRIFT

The Vacuum Drift System was designed to remove one of the most dangerous parts of casing preparation, which is using a snake and drift to confirm casing ID. This eliminates the hazards of conventional drifting while ensuring there are no deformities in the tubular. Efficiency without the noise. This design reduces operation noise by utilizing a vane pump instead of a blower creating 27 mercury units of vacuum force. With the unit fully mobile it can be utilized anywhere on-site, even in difficult-to-reach areas, with any length of hose. It contains an adjustable reverse function to push the drift if it becomes lodged in the tubular. Drift times per/joint depend on casing size and volume of air moved.

#RedefineTRS™

FEATURES

Drift Range: 2.63 - 13.63” (66.8 - 346.2 mm)

Vacuum Adjustment: 0 - 27 Hg (vacuum force)

Size: Length 45” (1,143 mm), Width 30” (762 mm), Height 75” (1,905 mm)

Weight: 400 lbs (182 kg)

Hose Length: X2 100’

VACUUM DRIFTING SPECIFICATIONS

Heading #3	Heading #3
165 CFM @ 1,150 RPM
27 HG (Mercury units of vacuum force)
13 HP Honda motor
Rubberized drifting ends for hoses

ALL SERVICES, ALL LOCATIONS

CONTACT US TODAY

Pipe Roller

PIPE ROLLER

The Pipe Roller was developed to enhance safety in tubular handling, addressing the risks associated with conventional pipe rolling methods. Traditional methods can lead to serious injuries, such as pinched fingers, hand injuries, and crushed body parts. The Pipe Roller minimizes these hazards, providing a safer, more efficient solution for rolling tubulars. Designed for repeated use, this tool improves handling practices by eliminating pinch and crush points, making it an invaluable asset for rig operations focused on safety and efficiency.

#RedefineTRS™

FEATURES

Lightweight design allows for repeated use as a hand tool

Tool sizes accommodate wide range of tubulars

Nytril design allows for easy tubular insertion, with no damage to connection

Horizontal force applied (forward or back to begin rolling the tubular)

Bearing assembly allows for quick release without recoil

Handle designed to eliminate pinch and crush points

SPECIFICATIONS

Heading #3	Heading #3
CASING SIZES AVAILABLE	4.5 – 5.5” (114.3 – 139.7 mm) 7 – 9.63” (177.8 – 244.6 mm)
HANDLING WEIGHT	4.5 – 5.5” – 11 lbs (5 kg) 7 – 9.63” – 14 lbs (6.4 kg)

ALL SERVICES, ALL LOCATIONS

CONTACT US TODAY

CRT Nubbin

CRT NUBBIN

The ProTorque CRT Nubbin was designed to protect both the CRT packer cup and the tubular connection when a Casing Running Tool is used. Damage can occur to the seal and thread profile of the connection if there is misalignment when inserting the CRT. Without a CRT Nubbin, damage can occur to the packer cup as it passes through the connection. The nubbin’s improved stab flank reduces interference when inserting the CRT.

#RedefineTRS™

FEATURES

Specialty sizes and connections available upon request

Inline time savings equates to more productive rig time & seamless operation

7 degree stab flank to protect packer cup and allow easy transition into the tubular

Full circle pry bar hole for easy removal

Reduced thread engagement for more efficient operation

Increased packer cup life

SPECIFICATIONS

Heading #3	Heading #3
SIZING	4.5 – 13.38” (114.3 – 339.7 mm)
AVAILABLE CONNECTIONS	API and most premium manufacturers

ALL SERVICES, ALL LOCATIONS

CONTACT US TODAY

Tether Ring

TETHER RING

The ProTorque Tether Ring was designed as a safety device for Casing Running Tools (CRT). The Bolt-On Replaceable Anchors protect the Grease Port of the Sealed Bearing, with load rated / shock absorbing anchor points, allow the operator to secure the Tether Ring and CRT to the top drive below any connection that might back out. In the event that the CRT becomes disengaged from the top drive quill, the anchor points and safety sling ensures it does not fall to the rig floor. The safety slings are attached to the bail anchors on the Top Drive for a secure anchor point.

#RedefineTRS™

FEATURES

Overhead securement for CRT Tools

Removes the hazard of a dropped object on the rig floor

Ring interchangeable to different CRTs

Tether Sub can be installed pre-job or onsite for torque verification

Clamping force activates dies with 7,500 lbs of bite force

Interchangeable dies / anchor points allow damaged components to be replaced while inspecting and retaining the Tether Ring after use

Play Video

SPECIFICATIONS

Heading #3	Heading #3
LOAD RATING	3,000 lbs (1,665 kg)
SHOCK RATING	40,000 lbs (18,182 kg) of force
FALL HEIGHT RATED	24” (60.9 cm)
RPM RATING:	120 RPM

ALL SERVICES, ALL LOCATIONS

CONTACT US TODAY